Site Notices
8/19/2014 4:57:02 PM
Author
Message
cgraham86
Member
Offline
Posts: 73
Feedback: 100% (14)
Posted: 4/7/2013 5:47:15 AM
Doing a new upper build for a 14.5" carbine length barrel, so I need to find the flash suppressor that will be welded/pinned. I want a non-mount AAC blackout (can't find one) and came across this from DD:

http://www.operationparts.com/Daniel_Defense_Superior_Suppression_Device_p/dd-04074.htm

Problem is I don't think it's long enough to push my barrel out to 16" (1.875" minus the thread length is probably just over 1.375 or 1/8" short). I also haven't heard anything about how it performs.

Thoughts on either of those fronts?

I have a vortex and can go with that, but wanted to look for some alternatives.
balloo93
Member
Offline
Posts: 4952
Feedback: 100% (122)
Link To This Post
Posted: 4/7/2013 6:08:24 AM
I believe you need at least 2 1/4". I used a Phantom to bring mine to length, but I had it laying around. If I were you I would do the vortex you have, I believe that will put you at 16.1".

BE SURE TO MEASURE barrel length with a closed bolt. Just to confirm it isn't 1. 14.7" or 14. something" shorter....
Gamma762
Member
Offline
Posts: 23566
Feedback: 90% (10)
Link To This Post
Posted: 4/7/2013 6:42:43 AM
Vortex is available pre-drilled, while Blackouts are very hard and tough to drill through.
This is...a clue - Pat_Rogers
I'm not adequately aluminumized for this thread. - gonzo_beyondo
CO, FL, MI, SC, NH - Please lobby your legislators to end discrimination against non-resident CCW permit holders
Hydra-shokz
INFIDEL
Offline
Posts: 1273
Feedback: 100% (76)
Link To This Post
Posted: 4/7/2013 7:35:30 AM
I can't use a flash hider so brake/comp whatever it is. I have a Battle Comp 1.5 on one 14.5 and a POF brake on another. I like the POF better. I would go with the Vortex in your situation. I reckon if you get one pre-drilled might need to time it if you want the weld at the bottom. A shim kit will help if you go this route.
www.area7precision.us
cgraham86
Member
Offline
Posts: 74
Feedback: 100% (14)
Link To This Post
Posted: 4/7/2013 7:42:54 PM
Originally Posted By Gamma762:
Vortex is available pre-drilled, while Blackouts are very hard and tough to drill through.


This is actually a really good point. I'm having a hard time finding a pre-drilled vortex, but I can imagine how the blackouts might be hard to drill.

Yeah this DD isn't long enough.
Roland_Brice
Offline
Posts: 1
Feedback: 100% (1)
Link To This Post
Posted: 4/7/2013 8:46:24 PM
I just had the same dilemma with a 14.5" BBL Adams Arms Tactical Elite upper. Since I live near Rainier Arms I went with a Battlecomp 1.5 and had them do the pin job. Got it back in 6 days. It looks mean! But I've yet to fire up that baby yet.
cgraham86
Member
Offline
Posts: 76
Feedback: 100% (14)
Link To This Post
Posted: 4/8/2013 1:30:21 PM
[Last Edit: 4/8/2013 1:30:46 PM by cgraham86]
Ug I hope it's not too loud for you!

I know I want basic flash suppression - not looking for a comp or muzzle break. However, making sure I don't get into a bind with the length is the issue. I don't have the barrel yet (in the mail), so I'm essentially guessing if I try to go with a shorter one than the vortex.

I chose to go with the DD extended:

Daniel Defense Extended

Just a little variety. The vortex I have is on my 16" barrel. I can switch them if I really want to. The ACC non-mount is 1/8" shorter than these.