User Panel
User Panel
User Panel
|
Posted: 5/15/2016 6:21:34 PM EDT
[#1]
This is a standard problem. Mine does it as well. There is a FAQ on their website that talks about the LRBHO. If following that doesn't work, I know a guy who ground a little bit of the metal off and it seems to work better now. I don't think I'll be doing that, but it's a possibility. Perhaps Rudy from Macon Armory has some insight on this? Otherwise, it's pretty much a known issue and very few seem to be able to get it to work.
|
|
|
|
Posted: 5/15/2016 6:58:24 PM EDT
[#2]
That great news I bought their lower for the reason of last rnd hold open . I bought rudys bolt and buffer its works great so far looks great also well put together
|
|
|
|
Posted: 5/15/2016 7:08:10 PM EDT
[#3]
I have this lower. I have the best luck with the ETS mags. You could also try extra power mag springs.
Mine isn't 100%. I don't mind, but some mags work better than others. |
|
|
|
Posted: 5/15/2016 10:26:42 PM EDT
[#4]
They can be finicky.....best advice I have is to trim the portion that touches the mag where it fits in the cutout in the follower.....and if you have the new type that just lays under the bolt catch....bend it up a little at a time until it catches. I have had success with using the standard bolt catch spring...but have trimmed 2 or 3 coils of it.....
It can be frustrating.....but it is just a balancing act.....just have to screw with it. Just reread your post OP...if it is catching sometime....just bend the piece that fits under the catch up a little.....that should get you working.... |
|
|
|
Posted: 5/16/2016 5:59:37 AM EDT
[#5]
I trimmed about 1.5 coils off the bolt catch spring and put Wolffe extra power springs in my mags. So far it's been 100% holding open after the last round.
|
|
|
|
Posted: 5/16/2016 7:24:59 PM EDT
[#6]
Quote HistoryQuoted:
I trimmed about 1.5 coils off the bolt catch spring and put Wolffe extra power springs in my mags. So far it's been 100% holding open after the last round. I bought 4 brand new glock mags and 3 of them work..............replaced the springs in 3 mags I had with Wolff extra power springs and the LRBO works fine................ |
|
|
|
Posted: 5/16/2016 9:21:27 PM EDT
[#7]
be careful with extra power springs.......they can place more load on the mag catch/notch interface.....and as the Mag catch is aluminum......it can wear the mag body in the long term....
|
|
|
|
Posted: 5/17/2016 5:46:00 PM EDT
[#8]
Trimmed the spring twice worked and didn't work have to try again sat.
|
|
|
|
Posted: 5/19/2016 3:46:51 PM EDT
[#9]
Greetings, Do you know if you have the "new" type of lever for the LRBHO? If you can search back in the archives, I posted photos showing the difference between them. Using the one that came with my lower (DDLES at the time), no matter how I tweeked it or the spring, I could never get consistent function. After installing the new one, 100%. Check into that with CQ10, they may be able to tell you which version your lower has. Good luck! Regards, Jim |
|
|
|
Posted: 5/19/2016 8:00:36 PM EDT
[#10]
Ok so thanks for the info where do you find the archives listing on this
|
|
|
|
Posted: 5/19/2016 8:11:21 PM EDT
[#11]
The "new" type is just flat where it fits under the bolt catch....the "old" has a turned up area with a hole that fits around the nose of the bolt catch.....
|
|
|
|
Posted: 5/19/2016 8:43:27 PM EDT
[#12]
Ok just checked it is flat so it is the new type now what to do
|
|
|
|
Posted: 5/19/2016 9:39:15 PM EDT
[#13]
I just bend the flat up a little.....did you install their weaker spring under the bolt catch?
On several I have cut the tab that contacts the mag to fit the cutout in the follower |
|
|
|
Posted: 5/20/2016 5:16:35 AM EDT
[#14]
Yes used the spring and cut it twice will try and bend the flat area up not sure which part in the mag area you are trimming
|
|
|
|
Posted: 5/20/2016 4:18:16 PM EDT
[#15]
not trimming the mag....just making sure the piece of the lever that contacts the mag follower fits in the little divot in the follower.
Quoted:
Yes used the spring and cut it twice will try and bend the flat area up not sure which part in the mag area you are trimming Shouldn't have had to cut the spring they sent...... |
|
|
|
Posted: 5/20/2016 10:01:01 PM EDT
[#16]
Didn't cut the spring they sent used another that was close to it cut that one
|
|
|
|
Posted: 5/22/2016 6:39:59 PM EDT
[#17]
Shot around 80rnds sighting in not a hicupp lrbho worked and had maybe 2-3 times it didn't hold shot decent with factory excellent with reloads out to 200 yards I was amazed .
|
|
|
Win a FREE Membership!
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
