Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel

Log In

A valid email is required.
Password is required.
Site Notices
Basic
  • Member
  • Nov 2000
  • USA PA, USA
Basic
  • Member
  • Nov 2000
  • USA PA, USA
  • Posts: 1951
  • Feedback: 100% (58)
  • Status: Offline
Posted: 6/6/2005 7:57:03 AM EST
My 94 2dr. 2wd. Explorer is very hard to get into gears. I know the clutch is only a couple of years (of light driving) old, so that is not likely the problem (and the master/slave cylinders were replaced at the same time).

Someone suggested trying to adjust the shift linkage.

Can anyone tell me how to do this (or where to access the linkage)?

I tried doing a search, but with a slow dialup connection, I couldn't find what I needed.

Thanks!!!
Gober Dober
Avatar
Bronze
  • Team Member
  • Jun 2004
  • USA TX, USA
Bronze
  • Team Member
  • Jun 2004
  • USA TX, USA
  • Posts: 1406
  • Feedback: 100% (19)
  • Status: Offline
  • Link To Post: Click
Posted: 6/6/2005 8:01:17 AM EST

Hydraulic Clutch Troubleshooting
By Jeff Fisher

If your 1984 or later Hydraulic clutch is acting up, as in, not fully disengaging the clutch when the pedal is pressed or the clutch pedal not fully returning after being pressed read on...

Before swapping out the clutch components because you are suspecting a worn throw out bearing, inspect the linkage for wear. In particular look at the point where the master cylinder push rod connects to the clutch linkage (it's located to the right of the steering column inside the cab). On some model years the master cylinder push rod is adjustable. I replaced my later model non-adjustable push rod with a newer unit from a newer truck out of a junk yard.

Pull the pin.

Take the push rod off the drop down arm.

Inspect the plastic bushing and replace it if it looks at all worn.

If the linkage is well worn adjust the length of the push rod, if yours is the type that can be adjusted, or attempt to find a newer adjustable rod from a junkyard. Just a tiny little bit of slop at this critical connecting point can cause a significant loss of travel in the master cylinder.

When making adjustments take care not to adjust the push rod out too far, too much adjustment will prevent the hydraulics from returning and could cause clutch slippage. All you need to do is take out all the slop between the master cylinder push rod and the drop down arm.

Your best bet it to inspect this critical connecting point and detect wear early enough so that a new plastic shim will prevent a problem. I replaced the plastic bushing with some brass shim material.

This is easy and cheap insurance to prevent future problems. Keep and eye on this high wear point and keep it greased.



www.ford-trucks.com/article/idx/9/075/article/Hydraulic_Clutch_Troubleshooting.html
If it's not an Armalite it's just another gun.

Visit <font color=red>http://www.gamingshark.com</font id=red> if you like playing video games.

Visit our Counter Strike Source Server @ 69.28.211.151
Basic
  • Member
  • Nov 2000
  • USA PA, USA
Basic
  • Member
  • Nov 2000
  • USA PA, USA
  • Posts: 1952
  • Feedback: 100% (58)
  • Status: Offline
  • Link To Post: Click
Posted: 6/6/2005 4:21:58 PM EST
Thanks for the info. The Master and Slave were replaced--not sure if the pushrod is a normal replacement item at the same time.

I did look, and there doesn't appear to be any slop.

I'm still wondering if there is a way to adjust the gear shift lever at the transmission.

Thanks!!

AFARR
Basic
  • Member
  • Jan 2004
  • USA NE, USA
Basic
  • Member
  • Jan 2004
  • USA NE, USA
  • Posts: 133
  • Feedback: 0% (0)
  • Status: Offline
  • Link To Post: Click
Posted: 6/6/2005 5:46:54 PM EST
The M5OD 5 speed is the typical manual trans in the exploders
The gear shift components are internal (except for the stick) and are not adjustable
Basic
  • Member
  • Nov 2004
  • USA TX, USA
Basic
  • Member
  • Nov 2004
  • USA TX, USA
  • Posts: 1068
  • Feedback: 0% (0)
  • Status: Offline
  • Link To Post: Click
Posted: 6/6/2005 5:55:42 PM EST
Pressure plates(springs)can collapse even when fairly new(two years is not new)

I have not seen an adjustable clutch in many years
Basic
  • Member
  • Jan 2004
  • IRQ IRQ
Basic
  • Member
  • Jan 2004
  • IRQ IRQ
  • Posts: 247
  • Feedback: 100% (111)
  • Status: Offline
  • Link To Post: Click
Posted: 6/6/2005 8:03:37 PM EST
You may also want to check the firewall area where the master cylinder is bolted to it, because that's a big weak spot on those vehicles. I had an 88 Ranger that developed a big crack in the firewall under the MC, which led to rough shifting because the pedal was pushing the cylinder through the firewall every time I tried to shift gears. If this is the problem, it won't matter how much you adjust the pushrod.
Basic
  • Member
  • Nov 2000
  • USA PA, USA
Basic
  • Member
  • Nov 2000
  • USA PA, USA
  • Posts: 1953
  • Feedback: 100% (58)
  • Status: Offline
  • Link To Post: Click
Posted: 6/7/2005 1:17:39 PM EST
Will get someone to push on the clutch while I check things at the firewall.

I did pull the push rod off, but it doesn't appear to be adjustable. Might play with it a bit more later to see what I can see.

Will keep trying (hate to have to put a rebuilt tranny into the thing..not worth the $1k parts price right now).

Thanks!!

AFARR
"I'm a Full Fledged Member".
Avatar
Bronze
  • Team Member
  • Nov 2001
  • USA OR, USA
Bronze
  • Team Member
  • Nov 2001
  • USA OR, USA
  • Posts: 5126
  • Feedback: 100% (13)
  • Status: Offline
  • Link To Post: Click
Posted: 6/7/2005 1:22:01 PM EST
[Last Edit: 6/7/2005 1:23:45 PM EST by MillerSHO]
Either you've lost pressure because of a leak or you have a bad clutch again.

The last Ford I had, to adjust the clutch pedal all you had to do was pull the clutch pedal towards you with your foot or pull it back with your hands.

You'll hear it click, when it taken up the slack.

This was a 90 Ford so it could be different now.

Hey Feinswine!
Avatar
Bronze
  • Team Member
  • Jun 2001
  • USA CA, USA
Bronze
  • Team Member
  • Jun 2001
  • USA CA, USA
  • Posts: 1222
  • Feedback: 100% (61)
  • Status: Offline
  • Link To Post: Click
Posted: 6/7/2005 1:28:28 PM EST
I had a 93 Ranger with the 4.0 and 5spd. Same trans probably as yours. Mine was getting real hard to change gears as well and finally it would only go into 2nd. On the top cover of the tranny where the shifter pokes through, there is a plastic ball that wears out. I had to buy a whole new top cover assembly since the ball is held in with two pins that are non removable.
A day late and a dollar short.
Basic
  • Member
  • Mar 2003
  • USA NY, USA
Basic
  • Member
  • Mar 2003
  • USA NY, USA
  • Posts: 216
  • Feedback: 0% (0)
  • Status: Offline
  • Link To Post: Click
Posted: 6/7/2005 1:35:06 PM EST
[Last Edit: 6/7/2005 1:38:31 PM EST by zeekh]
Try posting you question here:

www.ford-trucks.com/forums/


Lots of people that know their stuff
Top