Where can I find an AR type collapsable stock kit for the PTR HK91

5/6/2013 10:34:21 AM

I have the Choate folding stock for my PTR 91. Although it makes the rifle much more compact and easier to store as well as easier to get in and out of the car with, I do not like how I cannot adjust the length of pull. Although the PWS FSC HK m...

How To Remove Pins From G3 Recoil Rod

5/5/2013 5:12:08 PM

Hello. I am trying to replace the wood stock on my cetme with a G3 stock I got from cheaper than dirt. I'm following the simple directions on http://www.weaponeer.net/forum/forum_posts.asp?TID=8974&PN=2. I easily removed the pin fro...

Supressed HK93s and subsonic 223

5/5/2013 4:55:11 PM

Does anyone know if an HK93/C93 type will cycle with subsonic 5.56x45mm cartridges? I didn't know if being blowback instead of DI or Piston would be an advantage in this case. Thanks for any info on this.

HK USC Discontinued

5/5/2013 11:44:42 AM

I don't normally hang out at HKPRO but there is a new post/thread stating the USC has been discontinued. I always wanted one, I think it comes from me walking away from a NIB HK94 ($750ish) back in the late 70's early 80's at a gun show.

Replacing the hammer in USP Compact

5/4/2013 11:00:01 PM

I can take it somewhere to have it done. But I'm mechanically inclined and would rather take the chance to learn more about the workings of the weapon... Would this be a job that I could realistically take on myself? Anyone done it? <...

RTG shipping time

5/4/2013 4:53:05 PM

Anyone place an order with RTG lately? Just wondering how quick he's getting orders out lately.

Umarex HK MP5 A5 Removing the barrel shroud from the front sight

5/3/2013 10:01:28 AM

I am having a heck of a time trying to take the front sight assembly off of my Umarex HK MP5 A5 .22. I have a replacement Euro spec barrel shroud for an SBR project, but I can't figure out how to remove the existing one. Has anyone f...

Walther HK MP5 22lr

5/1/2013 3:54:26 PM

Will the Burris Fast fire fit on a B&T 10-266, I know its a bit much but I want a red dot, This is going to be a hoot to shoot

Mr556 SBR

4/30/2013 10:17:53 PM

Anybody cut down their HK MR556 to 10.4 bbl length?Any issues with doing this?

broken locking piece

4/29/2013 9:37:55 PM

So I have put about 500rds through my newly SBR'd MKE 94p. Everything looked great on it and it functioned 100% with various magazines. I took it apart today and cleaned it to find a the front of the locking piece was broken off. I orderd a new...

how do flat builds stack up to PTR

4/29/2013 9:48:09 AM

are PTR receivers hardened? the AK flat builds do not compare to say NDS 100% receivers as the flat receiver is soft and the NDS ones are heat treated like all other factory built rifles. is the same true for HK receivers?

CETME Stock Swap and 922 Compliance

4/28/2013 2:00:13 PM

Hello everyone. I just wanted to check here and see what everyone says. I have a CETME that has the wood stock and handguards. I want to replace them with the g3 wide handguards and HK stock. I wanted to know if this would be a pro...

NFA sear availability

4/27/2013 9:25:56 PM

I want to get my first sear/lower. Anyone have any good leads?

Newb question

4/27/2013 3:51:00 PM

Hello all, I'm not new to HKs, but I don't keep up with them As much as I do ARs, so I'm curious about something, And sorry if this has been covered. But why is hk not involved in the civilian market?, Excluding the...

PTR91 GI 7 62 NATO

4/26/2013 10:33:29 PM

These Rifles can shoot! https://www.youtube.com/watch?v=5qXPk7gul5I

CETME OD Stocks and Metal Peice That Stock Conects To

4/26/2013 10:59:54 AM

Hello everyone. I'm going to look like a complete idiot here, but I want to get some answers from the AR15 group that is usually pretty spot on with their info. I just got a new century arms CETME and want to add to it. One, I rea...

HK94 clone SW5 question

4/25/2013 6:59:08 AM

I just bought one over the weekend and when I took it apart I noticed there was no rear stock bushing. Is this normal from them or do I need to get one and weld it in.

MOVED Were moving to Wisconsin

4/24/2013 9:39:56 PM

Topic Has Been Moved.Click Here to go to the topic!

Black market parts anyone use these guys before

4/24/2013 6:42:36 PM

looking into buying from them, but I am unsure.

Lets see your G36 conversions

4/23/2013 8:02:04 PM

Mine started life as a SL8-6 bought new. I finished the conversion, through TBostic, in Jun 2010. My camera did not like the engravings but in person they are very sharp and clean. I just didn't feel like taking the pictures again....

Which MP 5 clone is best

4/22/2013 6:51:25 PM

I'm in the market for a MP5. While I cannot a afford a real HK94 as of yet. I've decided to look at buying a clone. I was hoping to get a few opinions on which clones are good and which to stay away from. Thanks

USP Compact 9mm Barrel

4/22/2013 1:02:10 PM

Does anybody here know where I might be able to acquire a USP Compact 9mm barrel? It is out of stock on hkparts.net and when I called ...

Pure porn

4/19/2013 7:42:58 AM

AR15.Com - Heckler & Koch

USPc 9 Barrel Threading

Evike s AirSoft AR mag adapter for G36 converted to hold real AR mag

Black market parts

Low profile Aimpoint mount for HK MP5 G3 91