Archived Posts » 59,726,163
Which loctite to use when installing scope base on Rem 700?
12/30/2011 2:34:40 PM
Subject pretty much covers the question. Is blue loctite enough to use on the screws holding the scope base to the receiver, or do I need to move up to red?
12/30/2011 2:44:31 PM
none, just tighten to the proper torque.
12/30/2011 3:07:40 PM
Originally Posted By CenterMass0:
Subject pretty much covers the question. Is blue loctite enough to use on the screws holding the scope base to the receiver, or do I need to move up to red?
Subject pretty much covers the question. Is blue loctite enough to use on the screws holding the scope base to the receiver, or do I need to move up to red?
Never use red unless you want problem later if you use loctite use the blue.
1/3/2012 2:08:26 AM
blue
1/3/2012 4:58:11 PM
Originally Posted By akuser-47:
blue
blue
Always blue.
1/3/2012 5:06:28 PM
Second post has it
Though technically the First guy is correct, go with blue for piece of mind
Though technically the First guy is correct, go with blue for piece of mind
1/21/2012 11:34:44 AM
My rule is Loctite on everything unless it has a lock washer. Blue 242 or quickstick 248 is what I use.
1/23/2012 8:26:39 PM
I always use Green, it's between the other 2 and you can still remove if necessary but gives you a stronger hold than Blue. I also coat the bottom of the base with the same thread lock to assure a more solid base and after proper screw torque the excess will squeez out, then simply wipe it off and you have also just eliminated any chance of water getting under the base and causing rust. The Rem receiver is steel and I use Badger Ordnance steel 20 moa bases and water getting between them IS gonna rust. This small little issue will ELIMINATE that possability and is still removable. Just another option to consider and thats just the way I do it..Best of luck with whichever way you decide.
1/23/2012 11:20:07 PM
Originally Posted By AK74play:
I always use Green, it's between the other 2 and you can still remove if necessary but gives you a stronger hold than Blue. I also coat the bottom of the base with the same thread lock to assure a more solid base and after proper screw torque the excess will squeez out, then simply wipe it off and you have also just eliminated any chance of water getting under the base and causing rust. The Rem receiver is steel and I use Badger Ordnance steel 20 moa bases and water getting between them IS gonna rust. This small little issue will ELIMINATE that possability and is still removable. Just another option to consider and thats just the way I do it..Best of luck with whichever way you decide.
I always use Green, it's between the other 2 and you can still remove if necessary but gives you a stronger hold than Blue. I also coat the bottom of the base with the same thread lock to assure a more solid base and after proper screw torque the excess will squeez out, then simply wipe it off and you have also just eliminated any chance of water getting under the base and causing rust. The Rem receiver is steel and I use Badger Ordnance steel 20 moa bases and water getting between them IS gonna rust. This small little issue will ELIMINATE that possability and is still removable. Just another option to consider and thats just the way I do it..Best of luck with whichever way you decide.
I was going to say that's what I use the blue for, makes a bed for the base and seals out moisture.
1/23/2012 11:34:52 PM
Loctite 222 purple or Loctite 242 blue will work for the tiny screws. Degrease it first with brake cleaner. It is a good idea to tap the driver with a light hammer while torquing. Don't tap on a torque wrench.
1/30/2012 11:01:04 AM
Purple
2/15/2012 3:10:00 PM
I use fingernail polish, plenty of that crap laying around 
Dissolve with acetone if need be.
Dissolve with acetone if need be.
2/19/2012 12:45:51 AM
I place a very small bead of clear silicone between my base and action to seal out moisture.
Also easier to remove than Loktite.
Also easier to remove than Loktite.
2/23/2012 10:55:13 PM
Blue loctite and torque them down , i use a Weaver Torque wrench
