Archived Posts » 59,757,950
Best Price on Noveske 7.5" Barrel & KX3
11/21/2011 9:49:23 AM
I have a pistol I'm building with the intent of turning it into a SBR. I would like to turn it into my version of a Noveske Diplomat. THe best I have found so far for the Noveske 7.5 " barrel/block/tube for $350 from Rainier, and $125 for the KX3. Anyone know of some better prices? Thanks!
11/21/2011 9:10:54 PM
If you are .mil or LEO try DSG Arms. They give a good discount.
11/22/2011 6:17:19 AM
Originally Posted By agBQ08:
If you are .mil or LEO try DSG Arms. They give a good discount.
If you are .mil or LEO try DSG Arms. They give a good discount.
Noveske also offers LEO and military discounts direct. I do not know if they are the same as DSG's discounts, but it is worth looking into for comparison.
11/22/2011 6:25:59 PM
DSG is the Best!!! Their prices are hard to beat for LEO Discounts.
11/22/2011 8:28:42 PM
http://www.americanspiritarms.com/chrome-moly-barrels/7.5-inch-pistol-barrel/
Heres one for $175
* Disregard, it's not a Noveske*
Heres one for $175
* Disregard, it's not a Noveske*
11/22/2011 8:51:20 PM
I have a beat to crap scratched up KX3 I can sell you...would work great if you wanted to paint it.
DSG arms would be my recommendation.
Your build is looking really good and if I were you I would just buy the barrel because you are so close to being done it doesn't matter!
DSG arms would be my recommendation.
Your build is looking really good and if I were you I would just buy the barrel because you are so close to being done it doesn't matter!
11/23/2011 7:05:17 AM
Thanks guys, I pulled the trigger on the Noveske 7.5" & KX3 yesterday and it's on its way. Now I just have to put in my form 1 and hurry up and wait, but I will be waiting with a nice pistol so it's all good.
11/23/2011 7:47:00 AM
Looking nice, have you had your lower engraved yet?
11/23/2011 8:27:50 AM
No not yet, I'll do it once my stamp comes back.
11/23/2011 8:00:29 PM
Originally Posted By VrodRay:
No not yet, I'll do it once my stamp comes back.
No not yet, I'll do it once my stamp comes back.
but if you do it now you won't have to wait to slap the stock on! hehe..
11/27/2011 12:17:19 AM
My understanding is that a stock can not be added unless the form 1 has been approved.
The Noveske 7.5" barrel, and the KX3 came in and everythg looks perfect. I hand tightened everything to see how it would look.
Here are a couple pictures.
The Noveske 7.5" barrel, and the KX3 came in and everythg looks perfect. I hand tightened everything to see how it would look.
Here are a couple pictures.
11/27/2011 1:32:04 PM
Very nice!!! What are the other details of the build?
11/27/2011 2:31:09 PM
Thanks!
Spikes Lower
BCM Upper
BCM Gunfigher CH
Spikes 9" SAR Rail
Spikes NiB LPK
Phase 5 ambi bolt catch & revolving sling attachment
Magpul AFG & MBUS
Spikes pistol buffer assy
Noveske 7.5" barrel w/ KX3
Eotech 553
Spikes Lower
BCM Upper
BCM Gunfigher CH
Spikes 9" SAR Rail
Spikes NiB LPK
Phase 5 ambi bolt catch & revolving sling attachment
Magpul AFG & MBUS
Spikes pistol buffer assy
Noveske 7.5" barrel w/ KX3
Eotech 553
11/28/2011 1:41:29 PM
Ran into a small issue when I began installing the barrel & FS. The Barrel nut on the SAR is a slip fit for the rail and it is just slightly smaller then the KX3. So with the KX3 installed on the barrel the rail would not pass by. However I did figure out a solution, but already used my only crush washer, so I will need to pick up another one today. I need to install the KX3 on the loose barrel after the barrel nut and gas block go first, then feed it down the front of the rail and out the bottom so the barrel can be torqued down.
Obviously this set up isn't ideal for quick interchangability but I have no need for that, so it's all good.
Obviously this set up isn't ideal for quick interchangability but I have no need for that, so it's all good.
11/28/2011 1:48:58 PM
Or you can torque on the KX3 with a strap wrench. That's what I did to get it seated in my TRX rail.
11/28/2011 6:22:07 PM
Originally Posted By RDTCU:
Or you can torque on the KX3 with a strap wrench. That's what I did to get it seated in my TRX rail.
Or you can torque on the KX3 with a strap wrench. That's what I did to get it seated in my TRX rail.
That too
I'm a complicated man, I need a complicated solution...haha
It's done, no problems. I'll post a new pistol build thread later w/ pictures
11/28/2011 10:31:13 PM
oh man! That looks real good. I just decided to go 10.5" and these photos are the first bit of regret... but in true arfcom fashion I'll probably get both.
Great build!
Great build!
